WPILibC++  2020.2.2-33-g65eab93
Error Defines

Macros

#define CTR_RxTimeout_MESSAGE   "CTRE CAN Receive Timeout"
 
#define CTR_TxTimeout_MESSAGE   "CTRE CAN Transmit Timeout"
 
#define CTR_InvalidParamValue_MESSAGE   "CTRE CAN Invalid Parameter"
 
#define CTR_UnexpectedArbId_MESSAGE   "CTRE Unexpected Arbitration ID (CAN Node ID)"
 
#define CTR_TxFailed_MESSAGE   "CTRE CAN Transmit Error"
 
#define CTR_SigNotUpdated_MESSAGE   "CTRE CAN Signal Not Updated"
 
#define NiFpga_Status_FifoTimeout_MESSAGE   "NIFPGA: FIFO timeout error"
 
#define NiFpga_Status_TransferAborted_MESSAGE   "NIFPGA: Transfer aborted error"
 
#define NiFpga_Status_MemoryFull_MESSAGE   "NIFPGA: Memory Allocation failed, memory full"
 
#define NiFpga_Status_SoftwareFault_MESSAGE   "NIFPGA: Unexpected software error"
 
#define NiFpga_Status_InvalidParameter_MESSAGE   "NIFPGA: Invalid Parameter"
 
#define NiFpga_Status_ResourceNotFound_MESSAGE   "NIFPGA: Resource not found"
 
#define NiFpga_Status_ResourceNotInitialized_MESSAGE   "NIFPGA: Resource not initialized"
 
#define NiFpga_Status_HardwareFault_MESSAGE   "NIFPGA: Hardware Fault"
 
#define NiFpga_Status_IrqTimeout_MESSAGE   "NIFPGA: Interrupt timeout"
 
#define ERR_CANSessionMux_InvalidBuffer_MESSAGE   "CAN: Invalid Buffer"
 
#define ERR_CANSessionMux_MessageNotFound_MESSAGE   "CAN: Message not found"
 
#define WARN_CANSessionMux_NoToken_MESSAGE   "CAN: No token"
 
#define ERR_CANSessionMux_NotAllowed_MESSAGE   "CAN: Not allowed"
 
#define ERR_CANSessionMux_NotInitialized_MESSAGE   "CAN: Not initialized"
 
#define ERR_FRCSystem_NetCommNotResponding_MESSAGE   "FRCSystem: NetComm not responding"
 
#define ERR_FRCSystem_NoDSConnection_MESSAGE   "FRCSystem: No driver station connected"
 
#define SAMPLE_RATE_TOO_HIGH   1001
 
#define SAMPLE_RATE_TOO_HIGH_MESSAGE   "HAL: Analog module sample rate is too high"
 
#define VOLTAGE_OUT_OF_RANGE   1002
 
#define VOLTAGE_OUT_OF_RANGE_MESSAGE   "HAL: Voltage to convert to raw value is out of range [0; 5]"
 
#define LOOP_TIMING_ERROR   1004
 
#define LOOP_TIMING_ERROR_MESSAGE   "HAL: Digital module loop timing is not the expected value"
 
#define SPI_WRITE_NO_MOSI   1012
 
#define SPI_WRITE_NO_MOSI_MESSAGE   "HAL: Cannot write to SPI port with no MOSI output"
 
#define SPI_READ_NO_MISO   1013
 
#define SPI_READ_NO_MISO_MESSAGE   "HAL: Cannot read from SPI port with no MISO input"
 
#define SPI_READ_NO_DATA   1014
 
#define SPI_READ_NO_DATA_MESSAGE   "HAL: No data available to read from SPI"
 
#define INCOMPATIBLE_STATE   1015
 
#define INCOMPATIBLE_STATE_MESSAGE   "HAL: Incompatible State: The operation cannot be completed"
 
#define NO_AVAILABLE_RESOURCES   -1004
 
#define NO_AVAILABLE_RESOURCES_MESSAGE   "HAL: No available resources to allocate"
 
#define NULL_PARAMETER   -1005
 
#define NULL_PARAMETER_MESSAGE   "HAL: A pointer parameter to a method is NULL"
 
#define ANALOG_TRIGGER_LIMIT_ORDER_ERROR   -1010
 
#define ANALOG_TRIGGER_LIMIT_ORDER_ERROR_MESSAGE   "HAL: AnalogTrigger limits error. Lower limit > Upper Limit"
 
#define ANALOG_TRIGGER_PULSE_OUTPUT_ERROR   -1011
 
#define ANALOG_TRIGGER_PULSE_OUTPUT_ERROR_MESSAGE   "HAL: Attempted to read AnalogTrigger pulse output."
 
#define PARAMETER_OUT_OF_RANGE   -1028
 
#define PARAMETER_OUT_OF_RANGE_MESSAGE   "HAL: A parameter is out of range."
 
#define RESOURCE_IS_ALLOCATED   -1029
 
#define RESOURCE_IS_ALLOCATED_MESSAGE   "HAL: Resource already allocated"
 
#define RESOURCE_OUT_OF_RANGE   -1030
 
#define RESOURCE_OUT_OF_RANGE_MESSAGE   "HAL: The requested resource is out of range."
 
#define HAL_INVALID_ACCUMULATOR_CHANNEL   -1035
 
#define HAL_INVALID_ACCUMULATOR_CHANNEL_MESSAGE   "HAL: The requested input is not an accumulator channel"
 
#define HAL_COUNTER_NOT_SUPPORTED   -1058
 
#define HAL_COUNTER_NOT_SUPPORTED_MESSAGE   "HAL: Counter mode not supported for encoder method"
 
#define HAL_PWM_SCALE_ERROR   -1072
 
#define HAL_PWM_SCALE_ERROR_MESSAGE   "HAL: The PWM Scale Factors are out of range"
 
#define HAL_HANDLE_ERROR   -1098
 
#define HAL_HANDLE_ERROR_MESSAGE   "HAL: A handle parameter was passed incorrectly"
 
#define HAL_LED_CHANNEL_ERROR   -1099
 
#define HAL_LED_CHANNEL_ERROR_MESSAGE   "HAL: Addressable LEDs only supported on PWM Headers, not MXP or DIO"
 
#define HAL_INVALID_DMA_ADDITION   -1102
 
#define HAL_INVALID_DMA_ADDITION_MESSAGE   "HAL_AddDMA() only works before HAL_StartDMA()"
 
#define HAL_SERIAL_PORT_NOT_FOUND   -1123
 
#define HAL_SERIAL_PORT_NOT_FOUND_MESSAGE   "HAL: The specified serial port device was not found"
 
#define HAL_SERIAL_PORT_OPEN_ERROR   -1124
 
#define HAL_SERIAL_PORT_OPEN_ERROR_MESSAGE   "HAL: The serial port could not be opened"
 
#define HAL_SERIAL_PORT_ERROR   -1125
 
#define HAL_SERIAL_PORT_ERROR_MESSAGE   "HAL: There was an error on the serial port"
 
#define HAL_THREAD_PRIORITY_ERROR   -1152
 
#define HAL_THREAD_PRIORITY_ERROR_MESSAGE   "HAL: Getting or setting the priority of a thread has failed";
 
#define HAL_THREAD_PRIORITY_RANGE_ERROR   -1153
 
#define HAL_THREAD_PRIORITY_RANGE_ERROR_MESSAGE   "HAL: The priority requested to be set is invalid"
 
#define HAL_CAN_TIMEOUT   -1154
 
#define HAL_CAN_TIMEOUT_MESSAGE   "HAL: CAN Receive has Timed Out"
 
#define HAL_SIM_NOT_SUPPORTED   -1155
 
#define HAL_SIM_NOT_SUPPORTED_MESSAGE   "HAL: Method not supported in sim"
 
#define HAL_CAN_BUFFER_OVERRUN   -35007
 
#define HAL_CAN_BUFFER_OVERRUN_MESSAGE   "HAL: CAN Output Buffer Full. Ensure a device is attached"
 
#define VI_ERROR_SYSTEM_ERROR_MESSAGE   "HAL - VISA: System Error";
 
#define VI_ERROR_INV_OBJECT_MESSAGE   "HAL - VISA: Invalid Object"
 
#define VI_ERROR_RSRC_LOCKED_MESSAGE   "HAL - VISA: Resource Locked"
 
#define VI_ERROR_RSRC_NFOUND_MESSAGE   "HAL - VISA: Resource Not Found"
 
#define VI_ERROR_INV_RSRC_NAME_MESSAGE   "HAL - VISA: Invalid Resource Name"
 
#define VI_ERROR_QUEUE_OVERFLOW_MESSAGE   "HAL - VISA: Queue Overflow"
 
#define VI_ERROR_IO_MESSAGE   "HAL - VISA: General IO Error"
 
#define VI_ERROR_ASRL_PARITY_MESSAGE   "HAL - VISA: Parity Error"
 
#define VI_ERROR_ASRL_FRAMING_MESSAGE   "HAL - VISA: Framing Error"
 
#define VI_ERROR_ASRL_OVERRUN_MESSAGE   "HAL - VISA: Buffer Overrun Error"
 
#define VI_ERROR_RSRC_BUSY_MESSAGE   "HAL - VISA: Resource Busy"
 
#define VI_ERROR_INV_PARAMETER_MESSAGE   "HAL - VISA: Invalid Parameter"
 

Detailed Description